#Cobra 148 gtl rfx 150 driver#
#Cobra 148 gtl rfx 150 manual#
#Cobra 148 gtl rfx 150 license#

Mount the microphone bracket on either side of the transceiver, using the two screws supplied. Any convenient location with good electrical contact (remove paint) may be used.ДҐ. Locate the accessory contact on most ignition switches by tracing the power wire from the AM broadcast receiver in the car.Д¤.

#Cobra 148 gtl rfx 150 driver#

This prevents the set being left on accidentally when the driver leaves the car and also permits operating the unit without the engine running. In automobile installation, +13.8V DC is usually obtained from the accessory contact on the ignition switch. Connect the red DC power input wire (with the fuse) to +13.8V DC. Most CB antennas are terminated with a type PL-259 plug and mate with the receptacle.ДЈ. Connect the antenna cable plug to the standard receptacle on the rear panel. Before drilling the holes, make sure nothing will interfere with the installation of the mounting bolts.Дў. If nothing will interfere with mounting it in the desired position, remove the mounting bolts. After you have determined the most convenient location in your vehicle, hold the COBRA 148GTL with mounting bracket in the exact location desired. Proceed as follows to mount the transceiver:ДЎ. Also provide a good electrical connection to the chassis of the vehicle. When mounting the bracket and radio to your car, make sure it is mechanically strong. The COBRA 148GTL is supplied with a universal mounting bracket. In automobiles, the transceiver is usually mounted below the dash panel, with the microphone bracket beside it.

Select a location that is convenient for operation and does not interfere with the driver or passengers in the vehicle. Plan the location of the transceiver and microphone bracket before starting the installation. To obtain maximum performance please read carefully the descriptions and operating instructions in this manual.ДЈ field effect transistors, 45 transistors, The receiver also features increased protection against cross modulation and strong adjacent channel signals. The COBRA 148GTL has a vastly superior receiver which includes an RF gain control and noise blanker circuitry effective in both AM and SSB modes., and an automatic noise limiter effective in the AM mode. This unit features advanced Phase Lock Loop (PLL) circuitry, which is used in the AM mode and in the upper and lower single sideband modes, providing complete cover age of all 40 channels shown below. The COBRA 148GTL transceiver represents one of the most advanced SSB/AM twoway radios ever designed for use as a Class D station in the Citizens Radio Service. SAVE YOUR SALES RECEIPT, THE CARTON AND вЂњPACKINGвЂќ MATERIALS FOR POSSIBLE FUTURE USE.

#Cobra 148 gtl rfx 150 manual#

Keep this manual for detailed information about your Cobra CB radio.

#Cobra 148 gtl rfx 150 license#

Replacement or substitution of transistors, regular diodes or other parts of a unique nature, with parts other than those recommended by Cobra, may cause violation of the technical regulations of Part 95 of the FCC Rules, or violation of Type Acceptance requirements of Part 2 of the Rules.Д¬itizens Band (CB) Radio operators are no longer required to obtain an FCC license to operate their CB equipment or provide station identification.ДЄn operator of a CB radio station is required to comply with the communications act and with the rules of CB Radio Operation. Thus, advertising is not allowed on CB Channels because that is вЂњbroadcasting.вЂќ (CB also includes a Class A citizens band and Class C remote control frequencies.)ДЇCC regulations permit only вЂњtransmissionsвЂќ (one party to another) rather than вЂњbroadcastsвЂќ (to a wide audience). The Class D two-way communications service was opened in 1959.

The Citizens Band lies between the shortwave broadcast and 10-meter Amateur radio bands, and was established by law in 1949. Use Channel 9 for Emergency Messages Only. Section IV: Operation.Д¬ontrols and Indicators.